Metal adapter included for 19" rack mounting (2 units can be mounted side by side in a 19" rack) UF-2064 H includes UF-2064 dual receiver, 2 FB-64 belt pack transmitters w/mic/line switches, & 2 HSM-X3 headset mics w/mini XLR.
FB-64 BODYPACK TRANSMITTER:
The bodypack transmitter operates in UHF band frequency w/PLL synthesized control. UHF 64 preprogrammed selectable frequencies to avoid interference. Various uni-directional electret condenser capsule
options. Use 1.5V x 2 AA size batteries for low operating cost.
FUNCTION DESCRIPTIONS: UF RECEIVERS: These stationary receivers are for use w/our 64-channel selectable
transmitters. The receiver operates in UHF band frequency w/PLL synthesized control. Powered by 12V DC.
(1) POWER BUTTON: Push the POWER button to turn the receiver on & off.
(2) CHANNEL SELECTOR: 64 different selectable can be selected used by
rotating the selector(s) or knobs.
(2b) SET: Push the SET button to lock the selected group & channel.
(2c) GR/CH LED: These LED indicates the power is on, & display which group & channel is on.
( 3) POWER INDICATOR: The indicator LED lights when the receiver is ready to operate.
(4) RF LEVEL INDICATORS: These LED lights to indicate that signal is being received. For the UF-1264 the RF LED show the diversity RF signal that is being used A or B. For the UF-2064 the RF LEd display which MIc is being received MIC 1 or 2
For the UF-8264 the RF LED is a 5 level RF LEVEL meter that displays the signal strength.
(5) LEVEL CONTROL: Rotary controls adjust the receiver's output level from the microphone to line level for matching the input sensitivity of the mixer or amplifier.
(6) ANTENNA: Fixed-length UHF antenna permanently mounted either on the front or on rear panel.
(7) DC OUT: Connect the supplied cable to the receiver & the microphone, & it takes around 10 hours to charge.
NOTE: THE UF-1064, UF1264, & UF2064 ARE THE ONLY MODELS THAT RECHARGE BATTERIES.
(8) UNBALANCED OUTPUT: Unbalanced 1/4" mono jack audio output provides unbalanced low-impedance output
(9) BALANCED OUTPUT: 3-pin XLR connector provides balanced low- impedance output
(10) SQUELCH ADJ.: The squelch adjusts the output level to prevent from the external noise. Setting the squelch too high will reduce the range of
the system. Set the squelch to minimum before turning the receiver on.
(11) DC IN: Input connector for the supplied AC adapter.
FM-64 HANDHELD MICROPHONE: The handheld microphone operates in UHF band frequency w/PLL synthesized control. UHF 64 preprogramed selectable frequencies to avoid interference. Uni-directional dynamic or uni-directional electret
condenser capsules w/different characters for various choices. Use 1.5V x 2 AA size rechargeable or regular batteries for low operating cost.
(1) GRILLE: Protects the microphone capsule & helps reduce breath sounds & wind noise. The grille for the various microphone capsules differ in appearance.
(2) LOW BATTERY LED: LED indicates battery status. Switching the power to "ON", the LED flashing once indicates that the transmitter has
sufficient power. If the LED stays on, it indicates that the battery has insufficient power & should be changed soon. If the status LED fails to flash, the battery is either dead or not positioned correctly, & you
should correct the positioning or change the battery.
(3) ON/OFF SWITCH: Turns transmitter power on & off.
(4) BATTERY Compartment: Insert two AA batteries into the Compartment & make sure that the polarity of batteries is correct.
(5) CHANNEL SELECTOR: Changes transmitter channel setting.
(6) BATTERY COVER: Push to expose battery Compartment & channel selector.
(7) COLOR CLIP: This color clip helps to identify the frequency for multi-channel
operation.
(8) CHARGING INPUT: The inserted rechargeable batteries can be charged
by using the supplied DC-plug cable connection to DC Out on the receiver. It takes up to 10 hours for charging.
|
Shopping Cart
